Tulsa cell phone repair : Screen Repair

BlackBerry BOLD 9700 Screen Repair _ LCD Guide.mp3

Tulsa cell phone repair BlackBerry Bold ninety seven hundred LCD replacement first you’ll notice that the BlackBerry is powered on.

So you want to do is powered off and you can simply just take the battery out of the device to power it off. Once it’s powered off then we can just take our flat pick and we can start getting to the screws. You’ll notice that there’s no screws on the back of the phone. There’s a hidden little. Compartment down here at the bottom of the BlackBerry that you want to take just your flat pick and just pull up and you know it pop off it pops off really easy and then you’ll notice there’s two screws underneath it. Now that is a T5 So you want to make sure that. You have the T5 handy when you start this repair. And. What you’ll do then is just take and. Just pull up just at the bottom here.

Tulsa cell phone repair And you’ll notice that it is pretty pretty easy.

Then you just work your way around the edges here.

Want to be careful here too because you don’t want to break the front faceplate housing. So just take your time and carefully just continue to do that. That wedging motion.

Tulsa cell phone repair And both of them has just two little prongs that stick into the back of the housing and that’s why it’s. So why don’t you point out where those clips are on the side of the face plate and you’ll see them there about midway up the frame here and you’ll see it as you can. There you go right here. Good. And then there’s one on the back on the other side as well. Then you’ll take and just lift up just a little bit and then just push up while working it back and forth and the the front faceplate will just pop right off. Now you can take and just remove the keypad from the from the surface it’s not held down by anything it’s just basically down on the board. Then you’ll notice that there’s four screws. That you’ll need to remove in order to get the circuit board up off of the. Back housing. And those are also two fives as well. Once those four screws are removed you’ll notice that there’s a flex connector up at the top of the the phone. You’ll need to take and pull that up. Back towards the top of the phone so that that’s out of your way it actually holds the LCD down. It’s the volume the volume in the ringer speaker. Once that’s done you can take. And you’ll just you’ll take and pull up that circuit board and it comes up really easy and then the back of the phone you can just set off to the side. Next there’s two little clips at the top of the LCD one here and one here.

What you’ll need to do visually to take your flat pick. No need to bend those up towards the top of the LCD or the top of the phone so that you can remove the LCD off of the circuit board because it’s held down here at the bottom by two clips as well as the two clips here so it doesn’t move around.

So they can serve as locks we’re just kind of Tulsa cell phone repair.

Locks the LCD tightly into place because you don’t want that LCD fit and loose into the. End of the circuit board. And

then after you’ve moved those out just the hair you’ll be able to take and just place your pick on the top right hand corner of that LCD and you’ll just wedge it down in there. And you’ll notice that the LCD will. Well before you do that you’ll need to take in you’ll need to unplug the LCD and the back of the circuit board which is on the right side of the circuit board and take and just unplug it from the from the circuit board so when it comes up it’s not. Ripping that flex. And when you first take it off it’ll be a little bit firmer because it’s actually adhered down to the to the circuit board Tulsa cell phone repair.

Got all three on tape.

And once the CD is off you’ll notice that the two clips that had been at the bottom of the phone are still there then you’ll just take. It and you’ll take the new LCD and just put it in. Likewise you want to remember to put the two tabs in the bottom in first so that they lock into their position just like so. And then take and press the LCD down. And once that’s down it will be flush all the way around. And then you’ll take your pick and you’ll tape the two prongs that you bent up to. You’ll need to use those to lock the LCD down into place and you can just take those and then those right back up into place they go they build up pretty easy.

I just want to reiterate it’s really important that you get the two little tabs on the bottom of the LCD to fall underneath those little slots. There you see in the in the gold. Frame there. So they slide underneath the bottom first and then you fold the top the whole city down to the rest of the circuit board and then like almost showing your for the tabs over on the top. To securely fastened that little city to that circuit board.

And so I switch to I switch to a horror. It’s tough. It’s a metal pick just to bend that surface up and sometimes with the plastic it won’t bend it as well. But if you have something harder like a pick you can use that to bend those those taps back up. Now once those are built back into to lock that LCD down then you can just flip the circuit board back around and just plug that LCD back into its position and you’ll notice a little clip here pretty easy you don’t have to put a lot of pressure just just a little bit and it’ll slide right in. Next you’ll take the back housing and you’ll put the put the. The circuit board in and you’ll notice on the left and right side there’s little. Buttons for the volume. And then also for the voice memo those might come up everyone saw you just have to put them back in the position that they go. They only go in one way. So if those come up don’t worry. Just put those back in and everything will be fine. Next you’ll take that circuit board and you want to put the bottom in first because there’s two little clips at the bottom that you need to go underneath and you’ll you’ll need to make sure that those clips that the circuit board is actually underneath those clips and which are digital it it’ll be just like so. And then it’ll just fall right into place and you’ll notice the charge points in place and then the microphone is put in place as well and there’s little notches at the bottom Tulsa cell phone repair.

So it doesn’t allow you to line it up wrong. But if you you know if you are in wrong it will actually sit up off of the. Back housing. Next they’ll just take and plug the sound back in for the ringer speaker at the top of the phone. And then after you’ve done that you’ll just take and put these four screws back in that we’ve removed from the circuit board just a few moments ago. All right. Next which you’ll take and you’ll put the keys back into the location they go and what you want to remember is to put the top in first because it lines up everything so that it just goes down smoothly. Then you’ll take and put the faceplate back on. I remember putting it down over the top first because that’s how it came off. And you just make sure that it clips and then you’ll feel it clip and once it clips then you’ll take and push the the two little taps back in that we’ve we were having a little bit difficult time to remove. And they’ll they’ll fall right back into place once you have the faceplate on right. Then just take and push the bottom down and the clips will clip them together. Next what you’ll do is take the two bottom screws that we’ve removed and we’ll put those back in to their slots Tulsa cell phone repair.

Point out the tabs to the lower cover piece to. Important to break those off because they are plastic and they and they can you know weaken.

Yeah. And you’ll notice that there’s there’s three little tabs at the bottom here and you want to make sure that as you pulling that up that you’re not breaking those tabs off. So what you’ll do once once the two screws are back in you’ll take and you put those in the bottom first and then you’ll just take and push in and it’ll clip right into place. It just just to make sure that the foam is back to normal. Well just take it and put the battery back in and we will look for the red light and then we will wait for a hourglass to appear on the screen once the hourglasses appear then you know that the LCD is fine.

Now you also go over real quick John.

The LCD on the ninety seven hundred. It has two versions. Correct. Yes. How do you know what version any particular BlackBerry Bold is on the back of the LCD.

There’s a there’s a number that’s at the very bottom of the LCD and you’ll notice that it’s in. Really it’s impressive and to the to the back of the LCD just real fine and you’ll have to get in some good light so that she can see it. There’s actually two different versions there’s the 001 And then there’s the zero zero 0 two on these. And the more common one is going to be the 0 0 2 but you actually really don’t know what it’s going to be until you physically disassemble the phone and look at the back of the video and you will have to dismantle the whole entire phone to get to that unfortunately but once you do find that number you can just get the the right LCD and everything will work fine.

So would it be safe to maybe stalk you know one of each LCD at all times just to be safe. Or you can do the repair there on the spot.

Right. That would be great to store both both CDs just so that you can get that customer in and out and satisfy the customer real quickly.

Good. All right. That Blackberry Bold too. Ninety seven hundred Tulsa cell phone repair