Tulsa cell phone repair : Best Technology

Tulsa cell phone repair I’m just going to turn this mid frame a little bit favorable to my positioning here. I take these three cables these flex cables and I peel them back just a little bit carefully. And I take the circuit board kind of like landing an airplane.

Tulsa cell phone repair I’m just going to tweak it between my thumb there and then I’m going to have it fall right in that little slot like so it just kind of tucks in maybe about a sixteenth of an inch once it’s found that touchpoint then I can start lowering the circuit board down into place and I’m going to make sure that it fits nice and flush against the screw threads on the bottom of the device down here by the buzzer. Once that’s all done I’m going to take one screw right down here which is it’s the circle that secures the circuit board over the buzzer a get down into place and that will secure the circuit board from shifting around and whatnot.

OK so once that’s done make sure. Right away that you have three cables down here one two three. Those are all three. They’re not tucked underneath the circuit board.

Now let’s plug those cables in real quick. OK. So we’re going to take that top one just carefully. Get that plugged into its connector and we have the one that’s directly underneath it and plug that in. These ones this one it just barely just line them up correctly and then press straight down. And here’s the third final one there that’s all press down.

Tulsa cell phone repair We have this little extra antenna connector. Let’s go ahead and just plug this one up. And these ones have small little cylinders that they plug into. And you want to be real cautious that you’re not pushing down real hard forcing the cable fitting should be a nice smooth plug up which That’s what we got right there.

Now before we move on to far let’s go ahead and take this gold washer for the top corner and this gold washer basically has two little legs. And we want to just pinch those two little legs like so.

Tulsa cell phone repair And we’re going to lower this right down into place over top of that top left corner of the circuit board and I just lightly position that on there. We’ll take the screws from the top left corner of the screw.

And we’re going to go ahead and just easily.

Tulsa cell phone repair Sometimes a fight like that. So what to do here. Get back out real quick. Start the process again.

It’s nice to have you watch and experience some of the small difficulties that you all have but you just got to have patience when you’re working with small stuff like this so don’t freak out.

OK. That looks pretty good right there. But it is go ahead and just pull that back like that make that screw thread just really the wheel itself.

There you go. Perfect.

Tulsa cell phone repair Once we get that on there let’s go ahead and take our camera now before we plug these two cables and we want to put our camera down into its compartment place in the back into the camera in first and then lowering it down into place is what we want. Carefully go ahead and just plug in that connector nice and secure and then we can bend the LCD connector which is the firm one. Get that down into place take an old touchscreen cable and will fall back down into place. We’re being real careful with those cables before we move on any farther. Now what we want to do is we want to pick up our flood head screwdriver and we want to take those big special number two screws and we want to put those back in there locations.

Tulsa cell phone repair So here’s the first one which is on the top right corner of the circuit board and just nice and easily screw that back down into place. You don’t want to overtighten it but just get it to where it’s tight. The next one which is just directly to the right of this connector heads slowly just threw that one in. And lastly the one on the bottom of the corner of the circuit board right here. These are kind of cool screws because they actually allow the other screw on top to secure it down into place.

Great. OK. Now that those special screws are in place where we’re going to do is we’re going to take the the black EMI shield noticed that there is basically two small little tabs on the bottom of that EMI shield. And we want to basically take those tabs and we want to go ahead and insert them into this shield right here.

Basically plant them first down and then she’ll blow you know they will fit in there perfectly.

When you get it set up just right.

OK good. I was just going a little bit today. So it fit back down into that she’ll then we just want to fold it down towards the top and we’ll go ahead and just start taking our other small screws starting with a white circle right there directly on the top that one is going to go into the top of that wacky and my shield.

And move it around to the left.

Here we go.

Sometimes we put too much pressure down on it.

He’ll make it jump off on you like that.

So starting softly and then finishing strong is good I guess.

OK.

Tulsa cell phone repair From this point what we want to do is let’s go ahead and take this funny looking metal piece here. AIDS with the connectivity of the antenna and we’re going to go ahead and turn her phone sideways. You’ll see that there is a metal strip here and then between that metal strip and this black EMI shield there’s a little tiny seam. And. We want this gold. Portion piece find that scene and we’re going to go ahead and just put it straight back down into its little place with a little leg coming down over top of that antenna connector.

And then we need to put that screw which is on the blue circle label number two down over top of that black washer.

OK good I basically was sticking up just a little bit so I made sure I just put a little pressure. So it stuck down flush into its little fitting there. OK. Let’s take our black speaker box and we want to basically position this down kind of angled down a little bit first and then push it down like just like I did right there.

I’m holding pressure down in that right now. I’m going to take that risk screw on the right go ahead and put that back down into place so it secures it tightly into its compartment. Now we need our black triangle washer and it’s basically going to get inserted just like that. And that position on the left corner of the speaker box. So let’s go ahead and just take that right now. Drop it right down into the slot Mike. So take the screw and secure that washer. You know we go. We’re getting really really close guys.

Now let’s take our black.

Wire here.

Tulsa cell phone repair We need to weave that back through its little channel system and then we need to him plug plug in the antenna connector into its small little cylinder fitting and these are the ones that you need to be really really careful with that you don’t get it off center and push down too hard because if you’re doing it then it’s going to be real difficult for you to. Fix it make it right. So just going to take my time here and wind it up nice and straight over time of its connector. And then I push it right down on there and getting making sure that my eyesight is really really in line with both pieces.

Define that right connection and then press and so that’s done now we can take our other black antenna cap cover and we need to put this back on top of its position so you can see the screw mount the way that the picture shown is the way that it’s position to go on top of the circuit board here.

All aid that piece right here with my black to take the screw off the screw mat which is just above the blue circle and to perfect it to get that straight just a little bit here. Your. Ego.

Came next. Let’s go ahead and bend that 93 over and then fold this down and connect it nicely into the circuit board up here on top. Not foreseen anything it will find its connector and when it does it will just snap right in. OK. Now we take our little shield and we’ll lay that over top. It only goes on one way. You can see on the screw mat the picture as shown is the way that it needs to be applied.

Take our screws on the side.

A lot of times will do is light it up and then I’ll just pinch it with the opposite hand so that black shield doesn’t slide all over the place as on securing the. Now. Let’s go ahead and remove that battery plastic tab. Get that. Folded over into its normal position. We’ll take our battery and we’re basically just going to plug in the battery Eyssen carefully. OK. And then we’ll basically plant the left side of the battery down and then fold it down into place.

Tulsa cell phone repair Once that is done we have one more screw which is on the blue circle number to secure the battery connector.

Now we’re going to use our brand new phone doctor’s back cover with the red frame looks real sharp. And we’re going to start at about it eighth of an inch high on both sides making sure it’s flush before we slide it into place once it’s like that. Give it a nice little push down the place and we’re going to finish this thing up with two final screws in the very bottom of the foam. And remember that’s not your Philips driver it’s your small antelope driver.

So you get you know where pool pressure and it’s fun. So everything’s working.

Screw.

The iPhone for Verizon CDMA last friend. No pretty with that red trim and the red button. Man that’s awesome.