Broken Arrow Iphone repair : Power button

Samsung Captivate i897 Repair LCD Glass Screen.mp3

Broken Arrow Iphone repair This is the Samsung captivate LCD digitize or replacement.

We will do first is just make sure the device is powered off and went new. If you don’t see anything after you press the power button just if there’s nothing on screen you can just go ahead and take the battery out and that will definitely make sure that it’s powered off on the back of the phone no notice. There are four screws that you can see here. And then there are two down here underneath this clip. When they do get those sticks out.

However first we’ll just take these Forsters out.

Broken Arrow Iphone repair Now the bottom two I think just slide this clip down just a little bit where you can see inside. And you’ll notice the screw is there. I always leave the screw in. I just loosen it all the way outside. You can take your Philips and just go all the way down to the. To the screw and then you’ll feel it when it starts to release.

Give it a good 15 turns or so. And.

Should be should be enough for you then take and do the same thing to the other side just close that one side and just open the other side up and you’ll see the screw. You can just take your flops and just get down in there and it doesn’t fall.

So the clip doesn’t come off. No the clip doesn’t come off. You just leave it in there.

Broken Arrow Iphone repair Just take and take the clip go back over. So it’s back to normal.

Now I want all six of those screws loose and you’ll notice that these up here typically will stay inside the phone.

You don’t have to remove him out of the back housing. I typically just leave him in there unless they come out like this one. That’s what you do next time. They

the captivate completely face torture and you’ll notice that there is a bedframe here on the side all the way down both sides.

And that’s where we’re going to separate the back housing from the actual LCD and the circuit board. You can just take your flat pick and just going that far right hand corner of the top of the fall and just work your way down.

You know pulling out on the on the phone. And you’ll notice that it’s that it’ll come out pretty easy. Once you get when one side started.

So. Now if you want to take.

Go to the top of the phone and notice that there is a clip up there as well and you want to just click that. This and.

Then. You’ll go to the other side and just start working your way down as well. Now once that’s released you’ll notice that it’ll just pop right out. I mean you don’t put any force on it you just basically. All right.

Now you’ll notice that there is a screw here right by the vibrating switch. You’ll need to remove that screw in order to get this whole sector out of the phone the circuit board itself. I just figure that one screw from the circuit board.

And just set it off to the side.

Broken Arrow Iphone repair Next you’ll notice you have the camera up here.

You can just take your flat pick just pick up on that and remove that from the actual frame and it comes up really easy.

Next you’ll go up to the to the speaker jack and just pull that up and just pull it to the side.

Then you go to the LCD and just pull that to the side as well.

And then you’ll notice that there’s a flex down here at the bottom and that’s for the touch portion of the front of the screen here with the buttons.

And you just move that off to the side. Then the final step before we can remove that circuit board is just to unplug the antenna at the right hand corner of the bottom of the circuit board and we can just now take and start to remove this circuit board and it’ll remove really easy once you get that antenna off and just set it off to the side.

Broken Arrow Iphone repair Now basically all we have to do is turn it back over and then we just have to be careful. You can take if you if you’re if you want to loosen up that three inch tape you can take some heat and just apply a little bit of heat here. I don’t use heat but if you wanted to you could there is a flex connector down here at the bottom of it just like the vibrate that you need to be really careful with it just so that you’re not so you’re not repeating that when you’re pulling this off of the the mid frame. So we start at the top and work my way down so I can avoid tearing anything down here.

And you can just take and just fly it just a little bit of pressure here. And you’ll notice that it’s coming out pretty pretty easy once it’s broken.

You know you don’t have to be careful with that when it’s broken because it’s already going to be.

Careful you know applying this little bit of work to the LCD so that when you do get down here to the bottom you’re not just flipping it across and then ripping that flex at the bottom of the song. And so I just stayed in just you know pedal off as much as I can in a fit snaps right before that flex connector. You can always just pull that off and move it out of your way so it’s not a stuff you know in your way.

You can just take that and put that off to the side next. You can just start here at the bottom right here. Left hand corner of the phone and you can just start chipping away at the glass. Just being careful of that flex the whole time so that you’re not picking it up as well.

Broken Arrow Iphone repair The Flex is basically you can it controlling those four buttons on the the front portion of the LCD.

A lot of times the Flex can not you know stick to the inside of that broken LCD digitizers. So John is just taking his time separating carefully the flex from the broken parts of the screen.

You’ll notice that it’s pretty simple once you get started that flex when it comes up with it if you just take a hold the flex down while you’re coming up. That glass. And once it comes all the way up you’ll know it’s pretty simple once once it gets all the way up there and if it starts to come up with it you can just hold it down and it comes up pretty simple.

And all the old they’ll see you’ll notice that there is a gasket that covers up the ears. And you want to take that off and replace it back onto the new digitizer and it’s just that. And you can take the new one and you can just set it on top here. Just like so.

And then.

What you can do after that is just take and just run your finger along the edges so that you know there’s no glass inside the the mid fret and you want to do that just to be careful so that you’re not putting the glass on the back of the new LCD and breaking it in the process of putting it on. After you’ve removed all the glass necks all you can do is take and just remove the tape that’s holding the three you. Are covering up the 3M so that when you put it back on it’s sticky. You can just remove that. Then you just take and apply. The digitizer making sure that the flex to the LCD is going through the little slot on the right hand side of the upper mid frame. And you can take and just put that in.

So once that goes all the way down just applied just a little bit of pressure and then a line up just right.

So. Just putting a little bit of pressure on it to make sure that three inches is sticking to the back of the head for me.

Broken Arrow Iphone repair After you’ve done that neck so all we have to do is start reassembling the form.

You can take the circuit board and place it back into the position in the appropriate location. And then just start plugging in the flex cables. So making sure that you plug that into the air. If you don’t then they won’t get reception.

Then you can take and put the camera back here.

So then I we need to put the screw back into the vibrator. Next we take the back housing and put it back on.

Line up everything and then you just take and put a little bit of pressure on it.

Go out and do the bottom first.

Broken Arrow Iphone repair Yeah I would. I go ahead and just make sure that bottom snaps and it’ll snap it really easy and then the sides will just snap and real real simple. Make sure that that bottom goes in. And then once the bottoms in the top will line up. Now we should just check everything to make sure everything’s moving right buttons are working in fields correct. Now we can take and just start scoring this six screws back into their look at their appropriate location.