Broken Arrow cell phone repair : iPhone 4 repair

iPhone 4 LCD Screen Repair Verizon CDMA Guide.mp3

This is a screen replacement for the rise in iPhone 4. First order of business is to make sure that the iPhone 4 is powered off. We can check that by pressing the home button at the bottom of the screen if it is powered on just press and hold the power button for about three seconds and you’ll see a screen come up that says slide to power off we’ll just do that first. Now let’s get into it.

Broken Arrow cell phone repair You’ll notice that there’s two screws at the bottom there are the Penta lobular screws what we need to do is make sure we get those out of the bottom before we can proceed.

And what we need to do is we need to make sure that we put those in the appropriate locations on the screen.

Matt.

What we’ll do is take both arms and just generally slide up on the battery door and it’ll come right up. First And first what we will do is you’ll notice that there’s a screw at the bottom.

Broken Arrow cell phone repair Tightening down the battery and what we want to do is first take that screw up.

Then we’ll take our our green pick and just gently gently pick up the battery or disconnect it then take the. Cab that they provide you to to gently pull up and pick that battery straight up.

Next we’ll go up to the top of the phone and you’ll notice there are six screws at the top that will need to slide off first to get the little black shield up off of it.

This whole time as we take the screws off we need to make sure that we put them in appropriately locations on this route map.

Next to just take and gently pry up on the this little clip and it’ll it’ll just pop up once once we move once it’s completely loose from the the circuit board itself it looks similar to that and then we’ll just play that off to the side here.

Next we’ll just move down the circuit board. You’ll notice that there’s a little shield holding down the end. The charge it at the bottom of a phone when they remove both of these screws so that we can unplug that charge for it.

Broken Arrow cell phone repair That should’ve just came loose and you can just pick that up and you place that over to the side as well. Then what we’ll do is we’ll just gently take and. Take that little flecks of. Make sure that. You’re being real gentle with that so that you’re not ripping or tearing. And then just move it off to the side just just like that.

Will continue down and you’ll notice that there’s two more screws here at the bottom that will need to to remove as well as the antenna cover that will need to remove the screw out of it as well so that we can unplug that antenna.

As you unplug the air as you uncover the antenna.

There’s a little cap that the screw is holding down that you have to make sure that you put back on when you get to that point. Assembling the phone. And it looks.

Like that.

As you take the bottom screw right here that. Holds down the ringer speaker. You need to make sure that you keep that black piece with it because it actually fastens that English speaker into place and one of to definitely keep track of that. Next we’ll go up here to the top of the phone and you’ll notice there are some five five connections up here that will need some plug. First you’ve got all these connections going to the vibrator switches and the on and the power flexes and when they do be real gentle with those.

But we need to unplug those before we can move on. You got all five of those on plug. Next we’ll move onto the camera. Unplug it and get it out of the way so that we can proceed to the screws that are underneath it. And once you get that camera out it just comes right out of place. Next there’s a screw up here. At the very top of the the phone that will need to replace are. We need to get out of the phone and there’s a little. I think it’s an antenna cable that are an antenna that hooks on to the to the camera and we need to remove that as well. And.

It’s it’s a gold gold. So it’s a place that on to the side.

Broken Arrow cell phone repair Next you’ll notice that as we took the screw out of the top here there’s another antenna cover that is covering up this this antenna underneath this. I’m going to pull that up as well. But first we want to do is there’s a there’s a little piece of 3M holding a little wire down here that we need to just gently pull up and just move off to the side here. It’s not that fragile but just make sure that you don’t rip it.

And then that piece just comes up and it looks similar to that right there.

Next fall. Well I’m the antenna that is up here at the top and it’s it’s pretty it’s pretty easy. It’ll it’ll pop just right up as as you just play upright apply a little bit of pressure to it next. There are three screws special screws throughout the throughout the circuit board that will need to remove. There’s one here here and here that we need to remove to get the circuit board to release from the. Mid-fi.

And. This whole time I’m putting the screws in the appropriate location on the screw.

Matt.

Next you’ll notice at the bottom of the phone there’s another antenna that we didn’t unplug quite yet. It’s a loop through two little prongs in the in the circuit board that will have to weave through. But we just need to unplug it first and once we unplug it it will then we can just leave it out of the circuit board itself. Just like that and then we’ll just press and put it down so that it’s out of our way. Next you’ll notice says as you do that the circuit board will gently start lifting up here. So what we’ll need to do is we’ll just need a pickup just to here and then pull down and it’ll release from its top. Half of the foam. Next you’ll notice down here in the bottom of the form there’s a vibrator switch.

That will need to remove and there’s a little screw hole here at the top that we can just take and we’ll put a flat pick underneath and we’ll remove remove that by British switch.

Step down pretty good. So you might have to put a little bit of pressure. To get it together. And it looks just like that and you’ll notice when and put it back in and it’s spotter’s and tape there as well.

Next what we’ll do is we will proceed to moving on to remove the English speaker out of the phone. And there’s one. One school left here at the bottom that we need to to remove. And then we’ll take them just put a little bit of pressure and it’ll just pull right up. Now that we’ve got all those circuit board in the ringer speaker out of the phone you’ll notice that there’s three screws on either side of the med friend that will need to loosen up in order to get started on removing the screen and you can just turn about one and half times on those. And they’ll they’ll be loosened enough to.

Broken Arrow cell phone repair To. Proceed on to the next step.

Next you’ll notice just like the iPhone 4 on AT&T there’s four screws in the corners of the phone. There is a black filp in the Verizon phone that is covering up one of the screws and what you need to do is just take and just take a little pick and just pull up that black tape. I’ve done this a couple times so that black tape is not there right now but you’ll see it when you’re replacing the screw.

Or when you’re removing the screw.

Broken Arrow cell phone repair This whole time remember to make sure that you put the put the screws in the appropriate locations on the screen so that when we go to putting it back together we’re not putting screws in different places. Now that all the screws are removed from the iPhone 4 screen now we can turn the phone back over and we can take a razor blade and we Broken Arrow cell phone repair can just gently pull up on that screen and remove that screen.