Broken Arrow cell phone repair : Best Service

Broken Arrow cell phone repair  And be real gentle with that guys because it can be it’s really easy to put too much behind it and you’ll ruin the circuit board with that in Tauber. So just be real real patient with it. No no no go in there just don’t put too much force behind this. Next what we’ll do is we’ll take the black clip that we took out earlier to holding the ringer speaker down and we’ll we’ll put it back into place here. And there’s only one way that it can go back. And so.

You’ll notice that it’s. That it looks like this at a triangle type state and just put it back into place itself.

Broken Arrow cell phone repair  Once it’s securely fastened then we’ll move on to putting the screws in along the circuit board here at the bottom so that we can put the. Charge for plugging back in. Now next what we’ll do is we’ll take that charge for flex and just spin it back down and plug it back in to the circuit board here. Remember just. You’ll feel it play again when you when you when you have it in the right location. That’s what we’ll do is we’ll move up here to the top of the to the top of the circuit board and we’ll just take these flexes and we’ll start plugging them in as well to the appropriate locations. And most of them will line up for with where they’re supposed to be.

So as sure as replacing the flexes and the the connectors. The line up just right.

Next what we’ll do is we’ll take and we’ll plug in the LCD and the dingy into the connectors on the circuit board as well. Next will take and put the screw in the top left hand corner of the the iPhone board and it’s got that made metal frame as well that we need to put down before we screw it down. And it looks it will and it looks just like this right here and in it only goes in one way. So you need to make sure that we put it in the correct way.

And once you have it in write it off it’ll just slide right into place.

Broken Arrow cell phone repair  And then just securely fastened the screwed down and then we’ll be OK. Next we’ll do what we’ll do is we’ll take the antenna cable that is in the top half of the phone and we’ll just make sure that we plug it back in as well as plugging it in. It’s just like the other one. Just be real gentle with it so that you’re not you’re not putting too much force behind it.

Because you do because you don’t want to more you know the center of it.

And the reason that you don’t put too much force behind is because you don’t want to mark the surface of the the antenna so that it’s not pulling service. And once it once it feels right you know you’ll know when it feels right because it’s it’s even flush with the circuit board itself the next what we’ll do is we’ll take and we’ll take the antenna cover and place it back over that into the.

Just like so on it it’ll look just like that it’s all black right there.

Next what we’ll do is we’ll go back down here to the bottom of the circuit board and we’ll will cover that antenna up as well.

With its antenna. And it looks like that.

And this whole time this is why it’s so important for you guys to put the screws on the screw mat and there appropriate locations. Next will take and put the cap that we pulled off earlier of the charge for it we’ll just put that cap back on there as well. And there’s only one way that it can go in there so once you get it lined up right then we’ll put the screws back in their appropriate locations.

Be patient with it because it’ll slide around just for a minute but once you get that first screw patting down the second one is really easy.

You could say something like to avoid you know the things you know slide around can take one finger and hold.

And what you’ll do when when you’re putting this this cap back on. Just make sure if it if you want to avoid from sliding around. Just play them over there and then you can you can keep it from sliding up and down too to where it just covers up. That’s. That’s what we’ll do is we’ll take and we’ll put the camera back in its little slot here. And what we can do is you’ll just take that camera and just put that top in first so that the that that little. Little cable is being pressed up or pushed up towards the top of the phone.

And you can just do that just it’s really easy and you’ll feel it slide into places where. And. Once it once it locks in the place the the cable will slide just right into its appropriate location.

Broken Arrow cell phone repair  The. Next what we’ll do is we’ll take the cap that we pulled off earlier or the little shield that we pulled off earlier and we’ll just put it in place. You’ll notice that the flex cable up here at the top of the phone is covering up where it plugs in or where it slides into underneath the circuit board. You want to take just a pic and just pull down just the hair on it so that it has room to guide it so that you have room to guide it into place that that would be best. And you’ll notice that as as you put into place here just put it down and then you’ll notice the flex is just out of place and then it’ll slide just straight up into place and then you can take and push that flex back up towards the top of the circuit board so that goes that show goes between the flex and the board. Right.

And that and you’ll notice that when you’re taking it apart that that that shield does go between the flex and the circuit board itself.

Now that we’ve got all the screws back in their appropriate locations what we need to make sure is that we take that little. Film that we’ve pulled up earlier and just place it back over the year Jack. Cover and just if it doesn’t stick down you can take some some tree and tape and just place underneath it and it all and it’ll go right back into place. And that’s what we’ll do is we’ll take the the battery cover that we’ve pulled up earlier and we’ll just unstick it from that 3M tape that we did earlier so that we can put the battery back into place. And what you’ll notice is you can put the battery in first and you’ll notice up at the top there that Flex is that it’s it’s down just a little bit here up at the top. And what we’ll need to make sure is that we’re that we push that back up so that when we’re putting the battery in it’s not smooshing that flex down and you can do that by just taking the top of the battery first and putting it in place and then gently just putting the plug in the battery back in and just make sure that you fill it in and you’ll feel it when it’s in place.

Broken Arrow cell phone repair  Just try.

And be gentle with that as well because you don’t want to make sure that you don’t you don’t ruin it and then just take and put the screws back screwed back in over the battery itself. Over the battery connector over the battery connector itself. Next just take the battery door and just put it. On like so. They thumbs and slide down.

And then put the tube into a level pin to lob the. Screws back into the iPhone 4. So you know.

And then just take and put the tube into lobular screws back into the iPhone 4. Used. To. Cut. Out of their.

Jobs to take it for.

Broken Arrow cell phone repair  We’re just it’s just you know put the audio up right here fading in and that’s all. No power on power at all. And that is the iPhone 4 screen replacement on the Verizon for